Ultrahigh Loading Copper Single Atom Catalyst for Palladium-free Wacker Oxidation

Wacker oxidation is an industry-adopted process to transform olefins into value-added epoxides and carbonyls. However, traditional Wacker oxidation involves the use of homogeneous palladium and copper catalysts for the olefin addition and reductive elimination. Here, we demonstrated an ultrahigh loading Cu single atom catalyst(14% Cu, mass fraction) for the palladium-free Wacker oxidation of 4-vinylanisole into the corresponding ketone with N-methylhydroxylamine hydrochloride as an additive under mild conditions. Mechanistic studies by ¹⁸O and deuterium isotope labelling revealed a hydrogen shift mechanism in this palladium-free process using N-methylhydroxylamine hydrochloride as the oxygen source. The reaction scope can be further extended to Kucherov oxidation. Our study paves the way to replace noble metal catalysts in the traditional homogeneous processes with single atom catalysts.     

Rate sensitivity and deformation mechanism of semi-crystalline polymers during instrumented indentation

Instrumented indentation tests using both constant loading rate (CLR) and continuous stiffness measurement (CSM) operation modes were performed to investigate the deformation mechanism and their sensitivity to the deformation rate in semi-crystalline polymers through the quantitative analysis of load-depth loading and unloading curves. The strain rate was constant during the CSM tests, while the strain rate decreased with the increasing of loading time in CLR tests. The mechanical response mechanism of the semi-crystalline polymers to these tests was very complicated because of the combined effects of strain-hardening in the crystal phase and strain-softening in the amorphous phase. Results show that the loading index m reflects the strain-hardening or strain-softening response during indentation. When m > 2, the mechanical response was due to the strain-hardening, and when m < 2, the response was due to strain-softening. A method based on the measured contact hardness was proposed to obtain the unloading stiffness, and the other mechanical parameters could then be determined according to the unloading stiffness.     

Flume testing of passively adaptive composite tidal turbine blades under combined wave and current loading

The tidal energy industry is progressing rapidly, but there are still barriers to overcome to realise the commercial potential of this sector. Large magnitude and highly variable loads caused by waves acting on the turbine are of particular concern. Composite blades with in-built bend-twist elastic response may reduce these peak loads, by passively feathering with increasing thrust. This could decrease capital costs by lowering the design loads, and improve robustness through the mitigation of pitch mechanisms. In this study, the previous research is extended to examine the performance of bend-twist blades in combined wave–current flow, which will frequently be encountered in the field. A scaled 3 bladed turbine was tested in the flume at IFREMER with bend-twist composite blades and equivalent rigid blades, sequentially under current and co-directional wave–current cases. In agreement with previous research, when the turbine was operating in current alone at higher tip speed ratios the bend-twist blades reduced the mean thrust and power compared to the rigid blades. Under the specific wave–current condition tested the average loads were similar on both blade sets. Nevertheless, the bend-twist blades substantially reduced the magnitudes of the average thrust and torque fluctuations per wave cycle, by up to 10% and 14% respectively.     

基于内聚力模型的快速荷载下CFRP-混凝土界面剪切剥离模拟

鉴于纤维增强复合材料(Fiber Reinforced Polymer, FRP)已在混凝土结构加固中普遍应用, 能有效提高结构的承载和变形能力. 为揭示动载作用下FRP-混凝土界面的剥离机理, 本文基于ABAQUS平台, 采用内聚力模型模拟CFRP-混凝土界面层, 实现了快速荷载下CFRP-混凝土界面剥离的高效模拟. 结果表明: CFRP表面应变在加载过程中由加载端向自由端方向传递, 随着加载速率的提高, 界面承载能力也随之提高; 界面峰值剪应力也存在显著的应变率效应; 模拟结果与试验结果基本吻合, 说明了新方法的有效性.     

水硬性石灰合成及拉破坏特性试验研究

水硬性石灰在欧洲石质文物修复和加固中获得了很大成功。我国的石质文物主要是砂岩,水硬性石灰的修复效果不好。为满足我国石质文物修复和加固的需求,本文以石灰石和黏土为原料,在950℃煅烧不同时间,制备出水硬性石,对试样的成分、微观形貌、收缩率、抗拉强度和拉破坏过程等进行了研究。结果表明:(1)试样中含有水硬性成分2CaO·SiO2(C2S);煅烧8h时,成分与欧洲水硬性石灰NHL5接近;1.5CaO·SiO2·xH2O(C-S-H)和CaCO3的含量随龄期的增加逐渐增加。(2)龄期1~3d,收缩率较小;龄期4~6d,收缩率以线性规律增加;7d以后,收缩率趋于稳定。(3)局部变形区随拉应力的增加而变大,邻近局部变形区逐渐合并,形成面积更大的应变局部化带;载荷超过峰值后,产生微裂隙;随载荷进一步增加,微裂隙扩展,贯穿整个试件,发展成宏观裂隙,使试件破坏。(4)抗拉强度随龄期的增加而增加,水硬性石灰中C-S-H、CaCO3等相互交织,构成空间致密体,使试件力学强度提高。合成的水硬性石灰物理力学性能与欧洲水硬性石灰NHL5相近,并且成分均匀、可控,在石质文物修复和加固工程中具有良好应用前景。     

基于八面体理论的岩石循环加-卸载本构模型及修正

探究岩石的受力特点及破坏特性是研究岩石地下工程安全性的关键,诸多学者都期望能在岩石本构模型的研究上取得突破性进展。在此背景下,提出了一种能够描述循环加-卸载条件下岩石的本构模型。首先,假设岩石的微元强度服从八面体剪应力理论并且微元破坏服从Weibull概率公式,将岩石本构中的损伤变量以及岩石微元强度表达式里包含的损伤因子进行本构变换,得到关于应力、应变等其他表现加-卸载下岩石损伤本构模型的参数,表示出岩石微元强度和损伤变量,再将得到的岩石微元强度和损伤变量代入所提出的岩石本构模型中,并进行等式变换得到一个函数表达式。通过将其与实验数据进行拟合对比分析,得出修正后的拟合参数,将其代入函数式中,得到损伤本构模型的修正式。最后将拟合参数进行必要的敏感性分析,得出各拟合参数的实际物理意义。     

The electronic properties and electron transport of sawtooth penta-graphene nanoribbon under uniaxial strain: ab-initio study

ABSTRACT

The electronic properties and electron transport of a sawtooth penta-graphene nanoribbon (SSPGNR) under uniaxial strains are theoretically studied by density-functional theory (DFT) in combination with the non-equilibrium Green's function formalism. We investigated the electronic structures and the current–voltage (I–V) characteristics of the SSPGNRs under a sequence of uniaxial strains in range from 10% compression to 10% stretch. In this strained range, carbon atoms still keep a pentagon network, but with the changing bond lengths. The C–C bond lengths change almost linearly with the tolerable strain. The value of the band gap of SSPGNRs can be depicted as a parabola under uniaxial strain. Our calculations show that the current is monotonous increase with compressive strain at the same applied bias voltage. In case of tensile strain, the variable rule of the current is different that it increases at first and decrease later. The fundamental physical properties (band structure, I–V characteristic) of SSPGNRs seem to be more sensitive to compressive strain than the stretch strain. The current intensity of the compressive-SSPGNR is by 2 orders of magnitude compared to that of the tensile-SSPGNR at the same strain in range from 6% to 10%. The results obtained from our calculations are beneficial to practical applications of these strained structures in SSPGNRs-based electromechanical devices.     

FeCoCrCuNi高熵合金裂纹及孔洞结构力学与微观构象演化机理的分子动力学模拟研究

本文采用分子动力学方法研究了FeCoCrCuNi高熵合金裂纹及孔洞模型结构在不同轴向拉伸应变速率下的力学与微观结构演化机理. 结果表明：应变速率越高FeCoCrCuNi裂纹结构对应更高的过冲应变和过冲应力，其主要原因是高拉伸速率会导致高强度的BCC结构及孪晶结构的生成，而BCC结构及孪晶结构的产生进而会抑制应力的下降，通过应力-应变曲线，可知FeCoCrCuNi裂纹模型在轴向应力作用下表现为塑性形变. 对于不同尺寸的孔洞FeCoCrCuNi裂纹模型的应力模拟与结构分析，可以得出：孔洞尺寸越大, FeCoCrCuNi裂纹结构对应的过冲应变和过冲应力越小，其主要原因是大尺寸的孔洞造成孔洞之间产生裂纹的，进而会影响这个材料的屈服应变和屈服强度.     

纵横载荷作用下功能梯度梁的弯曲和过屈曲

基于一阶非线性梁理论和物理中面概念,导出了纵横向载荷作用下功能梯度材料(FGM)梁非线性弯曲和过屈曲问题的控制方程,并获得了该问题的精确解;据此解研究了梯度材料性质、外载荷、横向剪切变形以及边界条件等因素对功能梯度材料梁非线性力学行为的影响,分析中假设功能梯度材料性质只沿梁厚度方向,并按成分含量的幂指数函数形式变化。结果表明:纵横载荷共同作用下,功能梯度梁的弯曲构形将有无限多个;随着梯度指数的增大,梁的变形减小,临界载荷升高;随着长高比的增大,横向剪切变形的影响减小。